2591- Expedition

CE-0100 - Shop Labor (per hour)

CE-0100

Shop Labor (per hour)

$144.00

CE-0100D - Labor to Dyno/Break-In a 9" 3rd. Member

CE-0100D

Labor charge for breaking in a 9" 3rd. member on the Currie dyno machine. Includes a decibel meter report.

$150.00

CE-0100QLP - Labor to Polish Ring & Pinion

CE-0100QLP

Labor to Polish Ring & Pinion

$200.00

CE-0102 - Labor to Weld On Leaf Spring Pads

CE-0102

Labor to Weld On Leaf Spring Pads

$144.00

CE-0104 - Labor to Shorten Rear Axle Housing (one side), Includes Straightening

CE-0104

Labor to Shorten Rear Axle Housing (one side), Includes Straightening

$159.95

CE-0105 - Labor to Install Aftermarket 4-link Bracket Sets

CE-0105

Labor to Install Aftermarket 4-link Bracket Sets

$575.00

CE-0106N - Labor to Shorten Housing (both sides) Using New Ends (ends not included)

CE-0106N

Labor to Shorten Housing (both sides) Using New Ends (ends not included)

$172.95

CE-0107 - Labor to Cut & Respline a Single Axle

CE-0107

Labor to Cut & Respline a Single Axle

$129.95

CE-0108 - Labor to Cut & Respline a Pair of Axles

CE-0108

Labor to Cut & Respline a Pair of Axles

$229.95

CE-0109A - Labor to Redrill a Pair of Rear Drums or Rotors

CE-0109A

Labor to Redrill a Pair of Rear Drums or Rotors

$144.00

CE-0109D - Labor to Drill an Additional Bolt Pattern in Axles/Drums/Rotors

CE-0109D

Labor to Drill an Additional Bolt Pattern in Axles/Drums/Rotors

$144.00

CE-0109H - Labor to Drill Access Holes in Axle Faces

CE-0109H

Labor to Drill Access Holes in Axle Faces

$99.95

CE-0109R - Labor to Change Register Hub Size on Axles

CE-0109R

Labor to Change Register Hub Size on Axles

$144.00

CE-0111 - Labor to Rebuild 9" or 8" 3rd. Member

CE-0111

Labor to Rebuild 9" or 8" 3rd. Member

$229.95

CE-0111B - Labor to Set-Up 9" 3rd. Member w/ ARB Air Locker

CE-0111B

Labor to Set-Up 9" 3rd. Member w/ ARB Air Locker

$349.95

CE-0111P - Labor to Polish Aluminum 9" Housing Center

CE-0111P

Labor to Polish Aluminum 9" Housing Center

$144.00

CE-0113 - Labor to Set-Up 9" or 8" 3rd. Member

CE-0113

Labor to Set-Up 9" or 8" 3rd. Member

$279.95

CE-0115 - Labor to Steelabrate Housing

CE-0115

Labor to Steelabrate Housing

$119.95

CE-0116 - Powder Coat Housing

CE-0116

Powder Coat Housing

$199.95

CE-0118 - Labor to Assemble 9" or 8" Rearend

CE-0118

Labor to Assemble 9" or 8" Rearend

$189.95

CE-0118F - Labor to Assemble Full Floating Rearend

CE-0118F

Labor to Assemble Full Floating Rearend

$259.95

CE-0120 - Labor to Remove Spring Pads

CE-0120

Labor to Remove Spring Pads

$119.95

CE-0122 - Labor to Disassemble and Diagnose a 9" or 8" 3rd. Member

CE-0122

Labor to Disassemble and Diagnose a 9" or 8" 3rd. Member

$99.95

CE-0124 - Labor to Remove Shock Mounts

CE-0124

Labor to Remove Shock Mounts

$144.00

CE-2099 - Charge Per Inch for Rearends Over 66" Wide

CE-2099

Charge Per Inch for Rearends Over 66" Wide

$5.49

CE-4044 - Labor to Polish Aluminum Gear Case & Pinion Support

CE-4044

Labor to Polish Aluminum Gear Case & Pinion Support

$239.95

CE-4044C - Labor to Polish Aluminum Gear Case

CE-4044C

Labor to Polish Aluminum Gear Case

$189.95

CE-4044P - Labor to Polish Aluminum Pinion Support

CE-4044P

Labor to Polish Aluminum Pinion Support

$99.95

CE-4044Y - Labor to Polish Billet Aluminum Yoke

CE-4044Y

Labor to Polish Billet Aluminum Yoke

$99.95

CE-4303BB - F9 Back Brace Installed on 3" Tube Housing (Front or Rear)

CE-4303BB

F9 Back Brace Installed on 3" Tube Housing (Front or Rear)

$420.00

CE-4303BBL - Lightened Back Brace Installed on 3" Tube Turn 9 Housing

CE-4303BBL

Our lightened back brace for 3" tube, Turn 9 fabricated drag race housings includes 2 windowed and dimple died 4130 chromoly brace halves, and installation labor. This brace will only fit housings that are a minimum of 43" wide, and a .5" pinion offset is mandatory.

$545.00